englebert
/
bluejay
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
Browse Source

chore: Clean up leftovers

main
Mathias Rasmussen 4 years ago
parent
8d19ac1338
commit
f9cbefaaf7
1 changed files with 5 additions and 23 deletions
Whitespace
Show all changes Ignore whitespace when comparing lines Ignore changes in amount of whitespace Ignore changes in whitespace at EOL
Split View
Diff Options
Show Stats Download Patch File Download Diff File
  1. 26
      Bluejay.asm

26
Bluejay.asm
View File

@ -123,10 +123,6 @@ DEFAULT_PGM_BEACON_STRENGTH EQU 80 ; Beacon strength
DEFAULT_PGM_BEACON_DELAY EQU 4 ; 1=1m 2=2m 3=5m 4=10m 5=Infinite
; COMMON
;DEFAULT_PGM_ENABLE_TX_PROGRAM EQU 1 ; 1=Enabled 0=Disabled
;DEFAULT_PGM_MIN_THROTTLE EQU 37 ; 4*37+1000=1148
;DEFAULT_PGM_MAX_THROTTLE EQU 208 ; 4*208+1000=1832
;DEFAULT_PGM_CENTER_THROTTLE EQU 122 ; 4*122+1000=1488 (used in bidirectional mode)
DEFAULT_PGM_ENABLE_TEMP_PROT EQU 7 ; 0=Disabled 1=80C 2=90C 3=100C 4=110C 5=120C 6=130C 7=140C
DEFAULT_PGM_ENABLE_POWER_PROT EQU 1 ; 1=Enabled 0=Disabled
DEFAULT_PGM_BRAKE_ON_STOP EQU 0 ; 1=Enabled 0=Disabled
@ -175,10 +171,10 @@ HIGH_RPM EQU 4 ; Set when motor rpm is high (Comm_Period4x_H less than 2)
Flags2: DS 1 ; State flags. NOT reset upon init_start
;RCP_UPDATED EQU 0 ; New RC pulse length value available
;RCP_ONESHOT125 EQU 1 ; RC pulse input is OneShot125 (125-250us)
;RCP_ONESHOT42 EQU 2 ; RC pulse input is OneShot42 (41.67-83us)
;RCP_MULTISHOT EQU 3 ; RC pulse input is Multishot (5-25us)
;RCP_DSHOT EQU 4 ; RC pulse input is digital shot
; EQU 1
; EQU 2
; EQU 3
; EQU 4
RCP_DIR_REV EQU 5 ; RC pulse direction in bidirectional mode
;RCP_FULL_RANGE EQU 6 ; When set full input signal range is used (1000-2000us) and stored calibration values are ignored
RCP_DSHOT_INVERTED EQU 7 ; DShot RC pulse input is inverted (and supports telemetry)
@ -199,15 +195,6 @@ Tlm_Data_H: DS 1 ; DShot telemetry data high byte
;**** **** **** **** ****
; RAM definitions
DSEG AT 30h ; Ram data segment, direct addressing
;Initial_Arm: DS 1 ; Variable that is set during the first arm sequence after power on
;Min_Throttle_L: DS 1 ; Minimum throttle scaled (lo byte)
;Min_Throttle_H: DS 1 ; Minimum throttle scaled (hi byte)
;Center_Throttle_L: DS 1 ; Center throttle scaled (lo byte)
;Center_Throttle_H: DS 1 ; Center throttle scaled (hi byte)
;Max_Throttle_L: DS 1 ; Maximum throttle scaled (lo byte)
;Max_Throttle_H: DS 1 ; Maximum throttle scaled (hi byte)
Power_On_Wait_Cnt_L: DS 1 ; Power on wait counter (lo byte)
Power_On_Wait_Cnt_H: DS 1 ; Power on wait counter (hi byte)
@ -219,7 +206,6 @@ Demag_Detected_Metric: DS 1 ; Metric used to gauge demag event frequency
Demag_Pwr_Off_Thresh: DS 1 ; Metric threshold above which power is cut
Low_Rpm_Pwr_Slope: DS 1 ; Sets the slope of power increase for low rpms
;Timer0_X: DS 1 ; Timer 0 extended byte
Timer2_X: DS 1 ; Timer 2 extended byte
Prev_Comm_L: DS 1 ; Previous commutation timer 3 timestamp (lo byte)
Prev_Comm_H: DS 1 ; Previous commutation timer 3 timestamp (hi byte)
@ -259,10 +245,6 @@ Adc_Conversion_Cnt: DS 1 ; Adc conversion counter
Current_Average_Temp: DS 1 ; Current average temperature (lo byte ADC reading, assuming hi byte is 1)
;Throttle_Gain: DS 1 ; Gain to be applied to RCP value
;Throttle_Gain_M: DS 1 ; Gain to be applied to RCP value (multiplier 0=1x, 1=2x, 2=4x etc))
;Throttle_Gain_BD_Rev: DS 1 ; Gain to be applied to RCP value for reverse direction in bidirectional mode
;Throttle_Gain_BD_Rev_M: DS 1 ; Gain to be applied to RCP value for reverse direction in bidirectional mode (multiplier 0=1x, 1=2x, 2=4x etc)
Beep_Strength: DS 1 ; Strength of beeps
Flash_Key_1: DS 1 ; Flash key one

Write Preview
Loading…
Cancel
Save